How do you hook up a throttle cable to a carburetor?

How do you hook up a throttle cable to a carburetor?

3:31Suggested clip 104 secondsInstalling the Carburetor, Clutch & Throttle Cables YZ125 Rebuild …YouTubeStart of suggested clipEnd of suggested clip

How do you install a throttle cable on a motorcycle?

8:08Suggested clip 118 secondsHow To Replace a 4 Stroke Throttle Cable – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do you reattach a throttle cable?

Push the new cable through the firewall and into the engine compartment. Step 2: Hook the new cable up to the accelerator pedal. Slide the new cable through the slotted hole in the accelerator pedal. Step 3: Reconnect the throttle cable to the retaining bracket.

How do you install throttle cables on a Harley?

8:08Suggested clip 121 secondsHow to Install Throttle Cables on your Harley Davidson – YouTubeYouTubeStart of suggested clipEnd of suggested clip

Why does my Harley have 2 throttle cables?

There are two cables because one of them is to open the throttle and one of them is to close the throttle in case the spring return doesn’t work. It’s a safety factor so get it fixed asap. The bike will be just fine with the main throttle cable,the other is,as posted above a safety cable.

Are throttle and idle cables the same?

Yes, the throttle(pull-open) cable is different from the idle(pull-close) cable. When measuring cables, measure the cable housing length. and be sure that you get the bend on the cable end that goes into the housing on the handlebars.

How do you attach throttle cable to grip?

5:24Suggested clip 102 secondsHOW TO REPLACE THROTTLE CABLE AND GRIPS ON – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do you install a throttle cable?

What is an idle cable?

The idle cable, as noted is just a safety feature. It can also come in handy as a spare, if your throttle cable breaks while you’re on the road, you can rig the idle cable to function as a throttle cable, (your throttle would operate in reverse, though).

How do you measure a Harley Davidson throttle cable?

5:30Suggested clip 89 secondsHow to Properly Measure Harley Davidson Clutch & Throttle Cables …YouTubeStart of suggested clipEnd of suggested clip

How tight should throttle cable be?

Most motorcycle manufacturers recommend about 2 to 3 millimeters of throttle free play, but over time the cables will stretch and settle into their housings and you’ll end up with more slack.

Do throttle cables stretch?

Sometimes a cable can become stretched over time, which will not only delay the response of the throttle, but can also leave the cable more susceptible to breaking. Delayed response may also be indicative of the need to have the cable slack adjusted.

How do you cut throttle cable length?

3:58Suggested clip 116 secondshow to make custom motorcycle cable lengths for throttle, clutch and …YouTubeStart of suggested clipEnd of suggested clip

How do you measure throttle cable?

5:30Suggested clip 25 secondsHow to Properly Measure Harley Davidson Clutch & Throttle Cables …YouTubeStart of suggested clipEnd of suggested clip

How do you make a choke cable?

13:41Suggested clip 113 secondsHow to make a choke cable – quickly and easily – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do you shorten a metal cable?

Cut the ball off and drill out the cable pieces. To reattach the ball slide it on the cable to the position you want it, using sliver solder flux coat the cable and ball, heat with a propane torch until glowing and then apply silver solder. when cool cut off the excess cable past the ball and clean off the residue.

How do you cut wire rope cleanly?

1:57Suggested clip 104 secondsCut Wire Rope Without Cutters – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do you cut cable TV cords?

5:18Suggested clip 113 secondsHow to Cut, Strip, and Crimp a Coax Rg-6 / 59 Cable – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do you keep wire rope from fraying?

1:44Suggested clip 104 secondsHow to keep steel wire cable ends together – YouTubeYouTubeStart of suggested clipEnd of suggested clip

What is the purpose of the core in wire rope?

The primary purpose of a core in wire rope is to provide a foundation or support for the strands.